top of page

Chemical Cleaning Solutions for Severe Calcium Scale Buildup

Writer: Gerry Wagner
Gerry Wagner
6 days ago
9 min read

The calcium crust on the hot-side channels is already bridging the corrugations, and last week’s CIP only dropped pH in the tank. Return liquor came back almost as dirty as it left. Approach has walked out. dP is still climbing on the same duty that used to sit quiet through a full campaign.


That is the unit we are talking about. Not a light film. Not a seasonal polish. Hard calcium carbonate locked into the plate pack, or into the tube bundle, thick enough that the chemistry never reaches the metal.


We clean these every week. The next useful decision is not “more acid.” It is whether this scale will still yield to a circulating clean, or whether the pack has to come out.


Why This Scale Is Different From Ordinary Fouling


Calcium carbonate does not sit like a soft organic slime. It nucleates on the hottest surface first, then grows into the corrugation valleys until neighbouring plates start to share a mineral bridge. Once that bridge is in, flow prefers the open channels and starves the rest.


You feel it as a slow walk in approach long before the high-dP trip. Operators chase flow. Someone opens a bypass. The remaining channels run hotter and the scale grows faster. That is how a “small fouling issue” becomes a locked pack. Shell and tube units are pulled on a different stand when the bundle has to come out.


Cooling tower fill that has been shedding hardness for a season will feed this exact deposit. So will a makeup line with no hardness control and a calorifier that never quite reaches the temperature the water treatment sheet assumed. The deposit chemistry is the same: alkaline earth carbonate, sometimes mixed with silica or iron, sitting where wall temperature is highest.


Removing heat exchanger scale of this type is a contact problem, not a tank-pH problem. If the acid never wets the bridge, the CIP log looks busy and the duty does not move. 


Reading DP and Approach Before You Commit to a Clean


Pull the last three months of hot-side and cold-side dP, plus approach at a known load. We want the same load point, not a mix of night and day figures. A pack that has doubled dP at the same mass flow is not “a bit dirty.” Half the channels are already out of the game Industrial radiators


Approach tells us where the heat is failing. If the approach is opened by several kelvin while dP is only mildly up, the remaining open channels are still carrying flow but the heat-transfer surface is insulated. That is a classic scale. If dP has spiked and approach is only a little worse, we may be looking at a blockage at the port or a collapsed channel rather than a uniform film. Cooling towers on the same circuit changing the water chemistry the pack has to live with.


Write the numbers on the work pack before anyone mixes a drum. We use those figures as the baseline for the clean, and again as the proof after the rinse. A chemical cleaning heat exchanger job without a before-and-after duty point is just a wet afternoon 


Photograph the CIP return at the start, mid-point and end. Colour, solids and foam tell us more in five minutes than a single pH strip.


When the CIP Loop Is the Wrong Tool


In-place circulation works when the channels still have a continuous path and the scale is still porous enough for acid to undercut it. It fails when bridges have closed the path, when gasket extrusion has pinched a port, or when the deposit is a hard calcite with a silica cap. Fans and pumps on that circuit are logged with the exchanger, not after the fact.


If the CIP pump is circulating happily at a low dP and the return is clear within the first half hour, the liquor is taking the easy route. You are cleaning the manifold, not the pack. Turning the pump up does not fix that. It just polishes the open lanes harder.


We Stop a CIP and Pull The

We stop a CIP and pull the unit when:


- Return stays loaded after a full volume turnover and a fresh charge. - Frame stretch or a known leak path means we cannot hold chemistry in the pack. - The unit has a history of channel blockage on this water. - Gasket age or plate material will not tolerate the contact time the deposit needs.


That call is cheaper on the day than a second failed CIP and a forced outage two weeks later.


How We Select Chemistry for Calcium on Stainless Plates


Severe calcium wants an acid that dissolves carbonate without chewing the plate or the gasket. On austenitic stainless plate packs we work with inhibited sulfamic or a buffered organic acid from the drum, dosed to the strength the deposit and the metal will accept. The inhibitor bottle goes in first. Always.


We do not put raw hydrochloric on a stainless plate pack. Chloride plus heat plus residual stress is how you buy stress-corrosion cracks you will not see until the next hydro. Carbon-steel shells and some tube bundles are a different conversation, with a different inhibitor and a tighter time cap.


Silica in the scrape changes the plan. Carbonate will fizz and lift. Silica will sit there and laugh at a mild acid. If the scrape from the port or the last opened pack shows a glassy skin, we flag that before we fill the tank. Mixed deposits need a sequenced clean, not a stronger single shot.


Temperature helps, but only inside the gasket limit. Warm liquor opens calcium faster. Over-warm liquor cooks the elastomer and then we are changing gaskets as well as plates. We set the bath to the gasket rating, not to the fastest lab curve Allied Heat Transfer.


Circulation, Heat and Contact Time That Actually Open Channels


Volume turnover matters more than tank size. We want the liquor to move through every remaining channel, reverse if the frame and the hoses allow it, and keep solids in suspension so they leave the pack instead of resettling in the corrugations. It sits with Oil coolers.


A dead-headed CIP, or a pump that is only stirring the tank, will give you a beautiful pH chart and a still-blocked unit. We fit the circuit so suction is from the true low point and discharge can be swapped end-for-end. On a stubborn pack we pause, let the acid soak against the scale face, then restart. Soak without flow only works if the channel still holds liquor against the deposit. A dry bridged lane does not care how long you wait.


We watch dP across the unit during the clean. A falling dP with a loaded return is the scale leaving. A flat dP with a clear return is the liquor missing the work. A rising dP mid-clean can mean debris has moved and lodged, that is a stop-and-inspect, not a reason to push


Contact time is decided on the metal and the gasket, not on hope. We would rather pull a pack that is still tight and finish the job in the workshop than leave acid sitting against a 10-year-old NBR gasket overnight.


Gasket, Port and Frame Limits During a Severe Clean


The gasket is the clock. Once swell, harden or take a set, the next start-up weeps at the carrier and everyone blames the clean. We check the elastomer type against the drum before a litre goes in. EPDM, NBR and the high-temperature grades do not share the same acid and temperature window chemical cleaning heat exchangers.


Frame compression has to be on the nameplate dimension before we circulate. A loose pack leaks chemistry into the drip tray and starves the channels. An over-tight pack pinches gaskets and can crack plates at the hanger. We measure tie-bar length, we do not guess from the last fitter’s paint mark chemical cleaning heat exchangers.


Ports collect the heaviest debris. If the unit has a history of port blockage we fit strainers on the CIP return and we open the port filters at the mid-point. Leaving a sock full of calcite in the line just recirculates grit across the remaining


On a cooling-tower-fed pack, expect sludge from the fill as well as hard scale. That sludge will blind a strainer in minutes. Budget the change-outs. Do not let a blocked strainer convince you the pack is


What We Measure While the Acid Is Moving


pH in the tank is a start, not the job. We want pH and a simple hardness or calcium check on the return, plus temperature at the unit, not at the drum. If return calcium is still climbing, the deposit is still yielding. If calcium has gone flat and pH is still low, either the work is done or the liquor has stopped seeing scale.


We keep a small sample of the start liquor and the finish liquor. Side by side they settle the argument later when someone asks whether the clean “did anything.”


Iron in the return on a stainless pack is a stop. That is metal, not scale. We flush, we inspect, and we do not top up the drum and carry on.


Our chemical cleaning crew runs that sampling on the unit, not from a desk. The plant engineer on shift stays in the loop on every stop/go call so the shutdown window does not get spent on a chemistry that has already finished its useful work.


Rinse, Passivation and Putting the Unit Back on Duty


Acid left in a corrugation becomes the next corrosion cell. We rinse to a set pH and conductivity, not until the water “looks clear.” On stainless we follow with a passivation step when the clean has been deep enough to strip the surface film. Skip that and the pack flash-rusts in the first hours on aerated water.


Refill on the process side only after the CIP circuit is broken and the hoses are capped. We have seen more re-fouling from a dirty CIP hose left on the port than from the raw water itself.


Bring the unit back on a known load and log approach and dP against the baseline you wrote down before the clean. That pair of numbers is the only close-out that matters. A shiny sample plate on the bench is not a duty.


If approach has come back and dP has not, we still have a hydraulic restriction, debris in a port, a crushed channel, or a plate that was already deformed. That is a pull, not a second acid shot.


When the Pack Is Too Far Gone and the Unit Has to Come Off


Some calcium jobs are workshop jobs from the first photograph. Plates that have been bridged for a season can be cleaned, but only after the pack is split, the gaskets are off, and each plate can see a directed jet and a controlled bath. Trying to do that work through a 50 mm CIP stub wastes the outage.


We open the pack in the workshop, map the worst plates, and decide which can go back. A plate with a knife-edge from the scale under a gasket groove, or a crack at a porthole, is scrap. Putting it back is how you get a cross-leak on start-up.


Where the Duty Still Has Years In

Where the duty still has years in it, replacement plate heat exchangers with a pattern and a material matched to this water stop the same scale from locking the unit in a single season. Channel geometry, plate thickness and the elastomer grade are chosen against the water and the temperature you actually run, not against a generic datasheet.


Shell-and-tube bundles with severe calcium in the tubes get the same honest call. If the mechanical clean after the chemistry still leaves wall loss or blocked tubes at the baffles, we retube or we replace. We do not sell you another drum and a hope.


Plant rooms that serve a building still have to leave the mechanical services in a state that satisfies the DCCEEW environment. A clean that strips a vessel and then returns it leaking, or a chemical store that does not meet the plant-room rules, is not a finished job. We treat the unit and the room as one system when we demob.


The Sample and the Photo We Need Before the Next Shutdown


Do this before you lock the next window. Scrape a coin-sized sample of the deposit from a port, a drain or the last plate that was opened. Bag it dry. Pull a raw-water sample from the inlet that actually feeds this unit, not from the tower basin on the other side of the yard. Photograph the CIP return on the last attempt, and export the last three months of approach and dP at one agreed load.


Send that pack to us with the gasket type, plate material, and the date the pack was last opened. We will tell you whether the next clean is an in-place circulation, a workshop strip, or a plate decision, and we will size the drum and the contact time against that deposit rather than against a generic calcium note.


Speak with us about the pack on that unit before the next shutdown.



 
 
bottom of page